Hot Melt Adhesive for Baby Diapers (adults)
Product Overview
Industrial-grade Hot Melt Pressure Sensitive Adhesive (HMPSA) engineered specifically for disposable hygiene products, including baby diapers, adult incontinence briefs, and underpads. Formulated with hydrogenated hydrocarbon resins and SIS/SBS block copolymers, this adhesive series delivers high initial tack, balanced peel strength, and reliable creep resistance under mechanical tension.
Optimized for high-speed slot-coating and spray-application systems, the formulation ensures clean cut-off without stringing at operating speeds exceeding 500 meters per minute. Available in block, pillow, and drum formats to match diverse bulk-melter feeding systems.
-
Super-Strength Diaper Construction Hot Melt AdhesiveMelt Viscosity (160°C): 4000 – 6500 mPa·s.read more
Softening Point: 90°C – 105°C.
Peel Strength: Industry-leading high structural tack.
Safety: Solvent-free, low VOC, and compliant with... -
Medium-Performance Nappy Hot GlueApplication Temp: 140°C – 160°C.read more
Melt Viscosity (150°C): 2500 – 4500 mPa·s.
Softening Point: 80°C – 95°C.
Appearance: Light yellow transparent block/granule. -
Easy-Flow Diaper Assembly AdhesiveApplication Temperature: 130°C – 150°C.read more
Melt Viscosity (150°C): 1500 – 3000 mPa·s.
Peel Strength: Low to medium-low (Gentle bonding).
Compliance: Solvent-free and compliant with... -
Lateral Side-Tape Fixing GlueApplication Temp: 150°C – 170°C.read more
Peel Strength: Very high; resistant to mechanical shearing.
Cohesion: Excellent; zero residue transfer.
Appearance: Light yellow transparent blocks. -
Wet-State Structural Reinforcement ResinWet Strength Retention: ≥70% after immersion in saline/urine.read more
Viscosity: Optimized for penetration into porous core materials.
Stability: Resistant to yellowing and chemical... -
Mechanical Fastener Bonding Hot MeltPeel Strength: Very high; specifically for difficult-to-bond non-polar plastics (PP/PE).read more
Application Temp: 150°C – 170°C.
Softening Point: 90°C – 105°C.
Internal Cohesion: High;... -
Standard Green Diaper Construction HMASolid Content: 100% (Solvent-free).read more
Application Temperature: 140°C – 160°C.
Compliance: REACH, FDA 21 CFR 175.105, and HG/T 3948-2025.
Open Time: 8 – 15 seconds (Optimized for... -
Backsheet Non-Woven Laminating AgentWet Strength: High retention after immersion in liquid.read more
Breathability Impact: Optimized for low coating weight to preserve vapor transmission.
Softness: Low modulus to maintain the... -
End-Seal Hot Melt For Baby DiapersApplication Temp: 140°C – 160°C.read more
Melt Viscosity (150°C): 2000 – 4000 mPa·s.
Softening Point: 75°C – 90°C.
Texture: Soft and flexible (Low hardness). -
Leg-Cuff Elastic Strand Anchoring GlueCreep Resistance: Premium-grade retention (>90%).read more
Service Temperature: 140°C – 170°C.
Base: High-strength SBC/SIS system.
Appearance: Water-white to pale yellow transparent. -
Diaper Multi-Layer Lamination Hot Melt AdhesiveProduct Description Innovation in diaper thinness relies on the efficiency of layer bonding, and our Diaper Multi-Layer Lamination Hot Melt Adhesive (Model 2788) is at the core of this technology....read more
-
Elastic Waistband Bonding Glue For NappiesBase Polymer: Premium SIS (Styrene-Isoprene-Styrene).read more
Creep Resistance: ≥90% retention under high tension.
Viscosity: Optimized for spiral and fiber spray application.
Odor:...

High Creep Resistance: Maintains elastic recovery and bond integrity under constant mechanical stress from spandex and Lycra strands.
Clean Processing: Low volatile organic compound (VOC) profile with minimal odor and zero nozzle carbonization during prolonged thermal exposure (150°C–170°C).
Wide Substrate Compatibility: Bonds securely across difficult nonwoven surfaces, polyolefin films (PE/PP), and breathable backsheets.
Low Add-on Level: High cohesive strength allows lower grammage application (0.03–0.05 g/m) without sacrificing peel performance.
Thermal Stability: Retains viscosity stability and resists yellowing or viscosity drop during 72-hour molten holding tests at application temperature.
Applications
Engineered for integration into automated manufacturing lines for disposable absorbent articles:
Baby Diapers
Ear attachment, frontal tape landing zone, core wrapping, and leg cuff construction.
Adult Incontinence Briefs
Wetness indicator bonding, chassis construction, and elastic leg gathering.
Underpads & Bed Pads
Backsheet positioning and tissue-to-film lamination.
Feminine Hygiene
Sanitary napkin positioning adhesive and release paper lamination.
Bonding Applications
|
Application Zone |
Recommended Adhesive Type |
Target Substrate Combination |
Primary Functional Requirement |
|
Construction |
HM-801 series |
Nonwoven to PE Film / Tissue to Fluff Pulp |
High tensile shear strength, permanent lamination |
|
Elastic / Spandex |
HM-802 series |
Spandex / Lycra to Nonwoven & PE |
Extreme creep resistance, high dynamic recovery |
|
Positioning |
HM-803 series |
PE Backsheet to Release Paper |
Clean peel, no adhesive transfer, residue-free removal |
Technical Specifications
|
Technical Parameter |
Test Method |
Typical Value (Construction) |
Typical Value (Elastic) |
Unit |
|
Appearance |
Visual |
White / Transparent Block |
Light Yellow Block |
— |
|
Viscosity @ 160°C |
ASTM D3236 |
1,200 – 1,800 |
3,500 – 5,500 |
mPa·s |
|
Viscosity @ 180°C |
ASTM D3236 |
600 – 900 |
1,800 – 2,800 |
mPa·s |
|
Softening Point (R&B) |
ASTM E28 |
85 – 95 |
100 – 110 |
°C |
|
Open Time |
Internal Method |
Short (1.5 – 2.5) |
Medium (3.0 – 4.5) |
Seconds |
|
Setting Time |
Internal Method |
Instant (< 0.5) |
Fast (0.5 – 1.0) |
Seconds |
|
Recommended App. Temp. |
— |
150 – 165 |
160 – 175 |
°C |
|
Specific Gravity |
ASTM D792 |
0.95 ± 0.05 |
0.96 ± 0.05 |
g/cm³ |
OEM & ODM Customization
Formulation Tailoring
Adjustment of open time, tack level, and viscosity profiles to match specific line speeds (300 to 800 m/min) and open-tank or closed-hose melters (Nordson, ITW, Robatech).
Color Customization
Standard white, clear, pale yellow, or custom pigment matching for brand identification.
Packaging Formats
Siliconized release carton boxes, PE meltable film bags, fiber drums, and bulk boxes tailored to automated feeder systems.
Quality Control
Raw Material Screening
Incoming polymer, tackifier resin, and plasticizer batches undergo strict testing for melt flow index, Gardner color, and softening point.
Rheological Testing
Brookfield viscometer and dynamic mechanical analysis (DMA) performed on every production lot to verify thermal stability and shear modulus.
Simulation Testing
Laboratory-scale slot die coaters and pneumatic peel testers validate bond strength and creep resistance prior to factory release.
Compliance Certification
Manufactured in ISO 9001:2015 certified facilities. Compliant with FDA 21 CFR 175.105 (indirect food contact) and REACH/RoHS regulations.
Packaging & Shipping
Standard Packaging:
20 kg / cardboard box containing 4 individually wrapped blocks in meltable PE film (5 kg each).
200 kg steel drums or fiber drums for bulk production lines.
Storage Conditions: Store in a cool, dry environment below 35°C, away from direct sunlight and heat sources. Shelf life is 12 months in unopened original packaging.
Logistics Support: Palletized and shrink-wrapped for standard container loading (20GP / 40HQ). Export documentation includes COA (Certificate of Analysis), MSDS, and hazardous-free transport certification.

Request a Quote & Trial Samples
To accelerate your technical evaluation and secure precise pricing, please provide your operational parameters when submitting an inquiry:
Target Application: Construction / Elastic / Spandex / Positioning
Dispensing Equipment: Nordson / ITW / Robatech / Other
Line Operating Speed: < 300 m/min / 300 – 500 m/min / > 500 m/min
Substrate Combinations: Nonwoven to PE Film / Spandex to Nonwoven
Estimated Annual Consumption: Metric Tons / Year
As one of the most experienced hot melt adhesive for baby diapers (adults) manufacturers in China, we also support customized service with low price. Please feel free to buy discount hot melt adhesive for baby diapers (adults) made in China here from our factory. For pricelist, contact us now.
acrylic magic tape adhesive, eva side tape adhesive, high peel strength hot melt adhesive